Used Woodworking Machinery CONTACTS MACHINERY, INC.
200 Round Lake South, Montcalm,
Quebec, Canada, J0T2V0
PHONE: 866-514-0890
Contact Us About This Machine

Homag KAL 310/A20/S2/CNC

Used Homag KAL 310/A20/S2/CNC | Edgebanders

Machine Information Sheet Date: 1/23/2018
Inventory #: C3255TS
Machine Type: Edgebanders
Manufacturer: Homag
Model: KAL 310/A20/S2/CNC
Year: 2004
Region: South West US
Voltage: 480/3/60
Can be transformed to required voltage for a nominal fee. Single phase available thru a phase converter.
Condition: Very Good
Machine Capacities: -Working level: 950mm (37 13/32")
-Minimum working width with 22mm (7/8") thickness: 55mm (2 5/32")
-Minimum working width with 60mm (2 3/8") thickness: 100mm (3 5/16")
Panel overhang: 30mm (1 1/8")
-Minimum workpiece thickness: 12mm (15/32")
-Maximum workpiece thickness: 60mm (2 3/8")
-Edge thickness strips: 0.4-20mm (0.16-25/32")
-Edge thickness coils: 0.3-3mm (0.12-1/8")
-Processing limits, strips: 900mm2 (1.39
-Processing limits, coils: 135mm2 (0.19
-Variable feed speed: 18 to 24m/min (59 to78 ft/min)
-Amperage service: 80A
-Control voltage: 24V
-Dust extraction;
-Mim. air velocity: 28 m/sec (92 ft/sec)
-Static pressure: 200 mm/ws (7.87"/ws)
-Air volume: 7980 m3/hr (4696 cfm)
-Compressed air;
-Connection size: 3/4"
-Pressure required: 7 bar (100 PSI)
-Adjustable in-feed fence
-Pre-milling unit (#3481) with two (2) motors 3kW, 9000 RPM for maximum tool diameter of 125mm (4 15/16").
-Noise projection stepped (#0424)
-Panel pre-heater (#2325)
-QA 34 quick melt gluing unit (#2123)
-Glue roller drive (#2141)
-Clamping device for glue pot (#2143)
-Glue container back-off (#2145)
-Multi-purpose magazine
-Magazine for six (6) rolls (#2458)
-Clipping unit (#2445)
-Magazine height adjustment (#2460)
-Pressure zone for gluing section Type C (#2507)
-CNC stepless axis for edge thickness adjustment (#2596)
-Snipping unit HL 05 (#3054)
-Adjustment chamfer, straight (#3114)
-Top and bottom flush trimming unit (#3209){Top and bottom rough trimmers}
-Set of TCT rough trimming cutters "I" system (#3900)
-Adjusting device - penumatic (#3251)
-Automatic multi-trimming unit (#3220) {Top and bottom tilting fine finish trimmers}
-Set of diamond cutters multi trim "I" system (#3930)
-Profile triming unit FF 12 (#3503) {4 motor corner rounding}
-"I" system diamond cutter R=3 T=4 (#3919)
-Pneumatic adjustment for profile trimming unit (#3536)
-Open space (#4511)
-Noise reduction enclosure (#0415/0425)
-Profile scraping unit (#4510)
-Pneumatic adjustment for profile scraping unit (#4522)
-Top and bottom edge buffing unit with oscillation (#4402)
-Electronic height adjustment (#6275)
-Electronic control with programmable memory (PLC)
-Monitor input NC 21 (#6313)
-Includes a 2nd glue pot

Contacts WW Machinery, Inc. sells pre-owned machinery on a first come, first served basis. Pre-owned machinery is not covered under any warranty or Government requirements. It is purchased "as-is - where-is, with all faults." Descriptions and specifications are to the best of our knowledge (some information is communicated via third party sources). It is strongly recommended that the machinery be inspected prior to purchasing to confirm the condition and specification. Additional charges such as crating and loading may apply.