Used Woodworking Machinery CONTACTS MACHINERY, INC.
200 Round Lake South, Montcalm,
Quebec, Canada, J0T2V0
PHONE: 866-514-0890
Contact Us About This Machine


Dimter Opticut 304R

Used Dimter Opticut 304R | Saws - CutOff, Miter, Radial Arm





 
Machine Information Sheet Date: 6/19/2018
Inventory #: C3769TS
Machine Type: Saws - CutOff, Miter, Radial Arm
Manufacturer: Dimter
Model: Opticut 304R
Year: 1996
Region: Eastern Canada
Voltage: 575/3/60
Can be transformed to required voltage for a nominal fee. Single phase available thru a phase converter.
Condition: Fair
Machine Capacities: -This machine is valued at over Cdn $200,000.00 if purchased new.
-It is complete and mechanically in very good condition. It has had very light use, however it does require a computer upgrade which will cost approximately US $3,000.00.
-8" Max. & 1" min. board width capacity -Thickness from 5/8" - 3-1/8" maximum -Board length from 16" min. - 16` maximum
-Out-feed length can be as short as
5"
-Cuts softwood or hardwood.
-Equipped with: 10 HP - 4,100 RPM Arbor motor, 15-3/4" diameter saw blade
-10 HP Servo drive feed motor -Accelerates material up to 750 FPM
-(3) pneumatically operated top rollers & (1) driven bottom drum roller
positively feeds board to saw, then stops quickly for saw to make precision cut
-System consists of:
-In-feed manual marking station
-In-feed arranged for 16` incoming lumber lengths.
-Measuring station:
-Cycle type roller conveyor where board length is measured by double wheel (smooth wheels) measuring system while top mounted luminescent camera detects crayon defect marks, up to (8)
grades detectable.
-Transport belt:
-10" wide in-feed belt between measuring station & saw
-16` length to process full length cap. board.
-Saw Station features:
-Saw stroke cylinder with acceleration and deceleration unit for very high cutting speed
-Material feeds up to 750 FPM
-Patented "Waste Gate" eliminates
short waste & end trims at saw blade.
-Out-feed & Sorting:
-10" x 20` long accelerating belt conveyor to sorting station with (5) kickers
-2 HP feed drive
-kickers are encoder pulse controlled and sort by any combination of length, grade and width; can be
programmed to kick singularly or to kick in "2s or 3s" for larger heavier boards
-End of belt is also programmable as a sorting station for long fixed lengths, salvageable finger joint lengths
or long waste pieces
-Separate control cabinet with: Industrial PC-type computer (multi-tasking, VME Bus system) with 15" VGA
monitor, 101-key board, hard disk for data storage & floppy disk drive; controls all system functions
including measuring, optimizing, cutting & sorting.
-Software program handles:
-(16) Board groups, each with (8) grades & (200) fixed lengths; production statistics on quantities, grades & times
-Graphical representation of boards
-Simulation of board data
-Full fault indication and "on-board" diagnostic
-Includes:
-Machine risers and base
-All owner`s and operator`s manuals and standard tool kit
-Also includes: marking station, 16` long in-feed deck, 20` out-feed table.
Sales Price: $14,500.00 CDN
Approximate Monthly Lease: $254.91 CDN
Approximate monthly payments are based on approximate lending rate considering 1st and last month down payment, 60 month term and $1.00 residual buy back. This approximate monthly payment amount is for budgetary purposes only. Based on US leasing rates.

Contacts WW Machinery, Inc. sells pre-owned machinery on a first come, first served basis. Pre-owned machinery is not covered under any warranty or Government requirements. It is purchased "as-is - where-is, with all faults." Descriptions and specifications are to the best of our knowledge (some information is communicated via third party sources). It is strongly recommended that the machinery be inspected prior to purchasing to confirm the condition and specification. Additional charges such as crating and loading may apply.