Used Woodworking Machinery CONTACTS MACHINERY, INC.
200 Round Lake South, Montcalm,
Quebec, Canada, J0T2V0
PHONE: 866-514-0890
Contact Us About This Machine

Barberan Automated Lacquer Application Line

Used Barberan Automated Lacquer Application Line | Finishing Equipment

Machine Information Sheet Date: 3/21/2019
Inventory #: C3611TS
Machine Type: Finishing Equipment
Manufacturer: Barberan
Model: Automated Lacquer Application Line
Year: 2009
Region: Eastern Canada
Voltage: 400/3/60
Can be transformed to required voltage for a nominal fee. Single phase available thru a phase converter.
Condition: Very Good
Machine Capacities: -Hours used: 8000
-Line speed: 1-12 m/min (3-39 ft/min)
-Carousel RPM: 1-25
-Two paint lines
-Eight (8) paint guns per line. One (1) back-up, total of seventeen (17).
-Product recovery
-Water based solvent
-Set-up times: 1 line - 2 mins, 2 lines - 0 mins
-Minimum width: 4"
-Maximum width: 60"
-Minimum length: 6"
-Maximum length: 120"
-Distance between parts: 3"
-Height of guns: 80-215mm (3 1/8" - 8 3/8")
-Cycle time at 4 m/min (13 ft/min): 13.5 min
-UV oven: 3 lamps
-Two (2) 3 lamp infra-red oven

-Barberan MMV-3500/1800 motorized conveyor
-Barberan MTB-3500/18 transport table with suction
-Barberan LP-1800 brush with suction
-Barberan RR-B8 automatic spray booth
-Barberan TEV-E+MT evaporation tunnel
-Barberan TEVT-E+MTAP transfer tunnel + evaporation
-Barberan TSP-MY infre-red drying tunnel
-Barberan HOK-E-3-1800 UV drying and curing tunnel
-Barberan MMV-3500/1800 motorized conveyor

-The ATX Airmix® gun, with its unsurpassed quality of atomization provides high finish qualityand important product savings. Worldwide recognized by professionals, ATX automatic guns are widely used in automatic finishing lines in most markets. The fluid circulation is available in the base (no pressure loss) or inside the gun (quick flushing).
-Excellent finish quality, reduced paint costs, cleaner working environment, lower booth maintenance.
-Quick service : only 4 bolts to unscrew, no need to remove hoses.
-Compatible with water-based materials.

-To be used with medium viscosity products. This pump can feed one or several guns.
-Compact design
-Easily integrated into a finish workshop
-High sealing capacity with singlelip seal
-Compatible with a wide range of materials
-Available in stainless steel version
-Compatible with water-based materials
-Compression ratio: 1,8/1
-Fluid volume per cycle (cm3): 85
-Number of cycles per litre of products: 12
-Air consumption (m3/h) at 30 cycles/mn at 4 bar: 2,1
-Fluid Output at 30 cycles/mn (l/mn): 2,6
-Free flow rate (L/mn): 5,1
-Max. air feeding pressure (bar): 6
-Maximum fluid pressure (bar): 10
-Maximum Fluid Temperature (°C): 60
-Sound level (dBA): 81
-Sealing Packings; Upper sealing GT cartridge with polyethylene packing, Lower sealing Acetal resin seal
-Weight (kg) - bare pump: 5
-Wetted parts: Aluminum, stainless steel
-Dimensions: 41 x 28 x 17 cm

Contacts WW Machinery, Inc. sells pre-owned machinery on a first come, first served basis. Pre-owned machinery is not covered under any warranty or Government requirements. It is purchased "as-is - where-is, with all faults." Descriptions and specifications are to the best of our knowledge (some information is communicated via third party sources). It is strongly recommended that the machinery be inspected prior to purchasing to confirm the condition and specification. Additional charges such as crating and loading may apply.